<?xml version="1.0" encoding="UTF-8"?><rss version="2.0" xmlns:dc="http://purl.org/dc/elements/1.1/"><channel><title>CR4 - Section&#x3a; Mechanical Engineering</title><link>https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;section&#x2f;mechanical-engineering</link><description><![CDATA[The Mechanical Engineering Section of CR4 includes forum and blog entries on motion and control, mechanical components, power transmission, etc.  This is the place to talk about the function and design of motors, bearings, gears, heaters, pumps, etc.]]></description><copyright>Copyright 2026</copyright><pubDate>Thu, 05 Nov 2026 13:54:28 EST</pubDate><generator>https&#x3a;&#x2f;&#x2f;cr4.globalspec.com</generator><item><title><![CDATA[Vena Contanta - Valves]]></title><link><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151757&#x2f;Vena-Contanta-Valves&#x3f;from_rss&#x3d;1]]></link><description><![CDATA[Hi to all,&#xa;&#xa;Based on the table below, is the pressure drop across a ball valve or a gate valve greater than that across a globe valve&#x3f;&#xa;&#xa;My question is&#x3a; How is this possible, considering that, due to its geometry, I would expect a globe valve to create lower-pressure points than a gate valve or a bal]]></description><pubDate>Thu, 05 Nov 2026 13&#x3a;54&#x3a;28 EST</pubDate><guid><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151757&#x2f;Vena-Contanta-Valves]]></guid><dc:creator>Billalex54</dc:creator><dc:subject>Mechanical Engineering</dc:subject></item><item><title><![CDATA[Air Compressor Pressure Drops During Operation]]></title><link><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151721&#x2f;Air-Compressor-Pressure-Drops-During-Operation&#x3f;from_rss&#x3d;1]]></link><description><![CDATA[Good day,&#xa;I am having an issue with an air compressor in our workshop. The compressor reaches the required tank pressure normally when there is no demand, but when we operate pneumatic tools the pressure drops and the compressor cannot maintain it.&#xa;I have checked for obvious air leaks and the intake]]></description><pubDate>Thu, 01 Oct 2026 14&#x3a;39&#x3a;59 EST</pubDate><guid><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151721&#x2f;Air-Compressor-Pressure-Drops-During-Operation]]></guid><dc:creator>MalcAndCheese</dc:creator><dc:subject>Mechanical Engineering</dc:subject></item><item><title><![CDATA[U Tube Bundle Inspection]]></title><link><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151713&#x2f;U-Tube-Bundle-Inspection&#x3f;from_rss&#x3d;1]]></link><description><![CDATA[Good day,&#xa;&#xa;I have query about the U Tube bundle, ECT and IRIS can be done on the straight tubes while the U tube bundle have curve, then how to do the inner inspection for the bend section of U bundle. the bend is at 90 degree.&#xa;&#xa;any tools in the market to perform for these tubes&#x3f;]]></description><pubDate>Sun, 20 Sep 2026 04&#x3a;20&#x3a;13 EST</pubDate><guid><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151713&#x2f;U-Tube-Bundle-Inspection]]></guid><dc:creator>Conan21</dc:creator><dc:subject>Mechanical Engineering</dc:subject></item><item><title><![CDATA[7 Line Facial Tissue Folding Machine]]></title><link><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151700&#x2f;7-Line-Facial-Tissue-Folding-Machine&#x3f;from_rss&#x3d;1]]></link><description><![CDATA[I have a problem with conveyor 2.&#xa;&#xa;When the knife is switched on, the paper starts to pull out regardless of the speed i use, and after few minutes the paper falls out completely from the front.&#xa;&#xa;I have tried to increase the &#x25; of conveyor 2, I have tried to increase the tension of conveyor 2, I have]]></description><pubDate>Thu, 03 Sep 2026 18&#x3a;27&#x3a;53 EST</pubDate><guid><![CDATA[https&#x3a;&#x2f;&#x2f;cr4.globalspec.com&#x2f;thread&#x2f;151700&#x2f;7-Line-Facial-Tissue-Folding-Machine]]></guid><dc:creator>Anonymous Poster</dc:creator><dc:subject>Mechanical Engineering</dc:subject></item></channel></rss>