Previous in Forum: Crystallization of Methamidophos   Next in Forum: Reduce the Evaporative Loss of Cooling Tower
Close
Close
Close
23 comments
Rate Comments: Nested
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3

Corrosion of Stainless Pipes and Carbon Flanges

12/10/2013 9:18 AM

The specifications for my piping project indicate that the pipes should be made of stainless steel, with welded flanges made of carbon steel.

Have you ever done this? Is there any corrosion to expect?

The fluid to be handled is vegetable oil. All this piping is indoors.

__________________
I am happy.
Register to Reply
Interested in this topic? By joining CR4 you can "subscribe" to
this discussion and receive notification when new comments are added.

Good Answers:

These comments received enough positive votes to make them "good answers".

"Almost" Good Answers:

Check out these comments that don't yet have enough votes to be "official" good answers and, if you agree with them, vote them!
Guru

Join Date: Jun 2010
Posts: 1296
Good Answers: 104
#1

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 10:10 AM

By 'welded', do you mean butt-weld, socket-weld, or slip-on? Are you sure the spec isn't calling for lap-joint flanges?

Register to Reply
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#2
In reply to #1

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 10:31 AM

Most of these flanges are slip-on, and some are weld neck.

Sorry but, what difference does that make regarding my question?

__________________
I am happy.
Register to Reply
2
Guru

Join Date: Aug 2012
Posts: 1071
Good Answers: 92
#4
In reply to #2

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 11:58 AM

Minimal product exposure with a slip on flange. Are you using a 303 or 304 pipe?

Sounds like someone's trying to cut corners where possible. Go with Lyn's recommendation of E309L wire.

Register to Reply Good Answer (Score 2)
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#8
In reply to #4

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 1:13 PM

304 pipe.

__________________
I am happy.
Register to Reply
Guru

Join Date: Aug 2012
Posts: 1071
Good Answers: 92
#12
In reply to #8

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 2:22 PM

Your major concerns would be water content and acid value of the oils- that's probably more important than galvanic potential- followed by the question of what you are doing with it.

The point is that your processing can make conditions worse (steam distillation etc.) for the materials of construction even though you're actually purifying the oils.

Why are you asking this question? Are you concerned with potential failure or are you asking this because it seems illogical to use SS pipe when the flanges are carbon steel?

Register to Reply
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#15
In reply to #12

Re: corrosion of stainless pipes and carbon flanges

12/11/2013 5:40 AM

I am concerned with potential failure due to corrosion in the seam between flange and pipe.

__________________
I am happy.
Register to Reply
Guru

Join Date: Aug 2012
Posts: 1071
Good Answers: 92
#18
In reply to #15

Re: corrosion of stainless pipes and carbon flanges

12/11/2013 8:46 AM

I have seen slip-on flanges welded on the inside instead (TIG)- this eliminates the possibility of material hold up in the socket area. Don't know if that's code or not. That is assuming that you are using Sch 10 or greater with slip on flanges- not SS thinwall butt weld with a CS slip on backing flange as noted elsewhere (a mistake that's surprisingly easy to make!).

In reality, you will get a bit of weld dilution into the base steel that will reduce the galvanic potential at that point. If the process oil is properly dried and of a suitable acid value, there shouldn't be much of a problem. Obviously it is a trade off.

Register to Reply
Guru

Join Date: Jun 2010
Posts: 1296
Good Answers: 104
#20
In reply to #18

Re: corrosion of stainless pipes and carbon flanges

12/11/2013 11:07 AM

Slip-on flanges should be welded inside and out, unlike socket-weld which are welded outside only. According to Eng-Tips.com, there may be some instances in some codes which only require a single weld. IMO, if OP is using SS pipe for corrosion control, then he should use SS flanges (or LJ). If CS is acceptable material of construction, then CS flanges are OK, even with SS pipe (but why spend $ on SS? - I don't know).

Register to Reply
Guru

Join Date: Jun 2010
Posts: 1296
Good Answers: 104
#5
In reply to #2

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 12:54 PM

As JNB pointed out, slip-on would give minimal product exposure to carbon steel. I thought maybe lap-joints with SS stub-ends were being used, but apparently not. BTW, the plant I worked at used carbon steel pipe for most vegetable oil (until it entered the process area).

Register to Reply
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#9
In reply to #5

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 1:16 PM

Same here. The only place where we use stainless steel for the oil is inside the process area. Everywhere outdoors, to and from the tanks, we use carbon steel.

__________________
I am happy.
Register to Reply
Guru

Join Date: Oct 2008
Posts: 42357
Good Answers: 1695
#3

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 10:46 AM

Does the project require that all welds be made with at least 309 Stainless welding wire? It should.

I'd require that all welds be painted with "anti corrosion" paint after welding.

Register to Reply
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#7
In reply to #3

Re: corrosion of stainless pipes and carbon flanges

12/10/2013 1:12 PM

It is being done this way.

__________________
I am happy.
Register to Reply
Guru
United Kingdom - Member - Indeterminate Engineering Fields - Control Engineering - New Member

Join Date: Jan 2007
Location: In the bothy, 7 chains down the line from Dodman's Lane level crossing, in the nation formerly known as Great Britain. Kettle's on.
Posts: 32212
Good Answers: 839
#6

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/10/2013 12:56 PM

Expect corrosion on any surface that is not stainless steel. Expect corrosion products in the fluid unless all wetted parts are stainless with compatible elastomers at joints. That should mean that the pipe will be thin-walled stainless with slip-on flanges, probably pre-painted. If the vegetable oil is for consumption, then food-grade stainless should be the only metal in contact with it. Some degree of internal polish might be expected, as would a clean-in-place facility somewhere on the P&IDs.

Try to avoid welding these metals as the heat-affected zone is where the corrosion will start.

__________________
"Did you get my e-mail?" - "The biggest problem in communication is the illusion that it has taken place" - George Bernard Shaw, 1856
Register to Reply
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#10

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/10/2013 1:17 PM

Does anyone know the galvanic potential of this battery (carbon steel vs SS)?

__________________
I am happy.
Register to Reply
Guru

Join Date: Oct 2008
Posts: 42357
Good Answers: 1695
#11
In reply to #10

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/10/2013 1:47 PM

Oh, come on! Look it up yourself.

Quit asking others to do your job for you.

Get a chart, print it out and hang it on your wall.

Register to Reply
Power-User
Engineering Fields - Agricultural Engineering - Agricultural Mechanization Technical Fields - Technical Writing - Translator Technical Fields - Education - Fluid Power Uruguay - Member - Born and raised.

Join Date: Aug 2006
Location: Montevideo, Uruguay
Posts: 474
Good Answers: 3
#17
In reply to #11

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/11/2013 5:47 AM

Lyn, don't be rude, I was asking because I have looked for it and couldn't find it.

However, when I tried to paste here a table to show you, it turned out that table DID have the galvanic potential of steels. Sorry to bother you.


Anodic Index

Metallurgy

Index (Volt)

Gold, solid and plated & Gold-platinum alloy0.00
Rhodium plated on silver-plated copper0.05
Silver, solid or plated; monel metal & High nickel-copper alloys0.15
Nickel, solid or plated, titanium and alloys & Monel0.30
Copper, solid or plated; low brasses or bronzes; silver solder & German silvery high copper-nickel alloys; nickel-chromium alloys0.35
Brass and bronzes0.40
High brasses and bronzes0.45
18% chromium type corrosion-resistant steels0.50
Chromium plated; tin plated; 12% chromium type corrosion-resistant steels0.60
Tin-plate; tin-lead solder0.65
Lead, solid or plated; high lead alloys0.70
Aluminum, wrought alloys of the 2000 Series0.75
Iron, wrought, gray or malleable, plain carbon and low alloy steels0.85
Aluminum, wrought alloys other than 2000 Series aluminum, cast alloys of the silicon type0.90
Aluminum, cast alloys other than silicon type, cadmium, plated and chromate0.95
Hot-dip-zinc plate;

galvanized steel

1.20
Zinc, wrought; zinc-base die-casting alloys; zinc plated1.25
Magnesium & magnesium-base alloys, cast or wrought1.75
Beryllium1.85
__________________
I am happy.
Register to Reply
Guru

Join Date: Oct 2008
Posts: 42357
Good Answers: 1695
#19
In reply to #17

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/11/2013 8:55 AM

Everybody involved in this thread has gone out of their way to give you sound advice.

Galvanic corrosion tables, charts and figures are available in thousands of locations and are childishly easy to attain.

You claim to be an "Industrial Mechanical Engineer, Specialized in Postharvest and Grain Processing".

EVERY time you come here you ask us for help! You earn at least part of your salary using information we provide to you free of charge.

I don't think it is rude to ask you to perform the simpler tasks before you to satisfy your customer.

Register to Reply
2
Guru
Safety - Hazmat - New Member Engineering Fields - Retired Engineers / Mentors - New Member Engineering Fields - Piping Design Engineering - New Member Hobbies - DIY Welding - New Member Fans of Old Computers - PDP 11 - New Member

Join Date: Feb 2007
Location: Stronger Than The Storm
Posts: 2394
Good Answers: 203
#13

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/10/2013 2:49 PM

gussosa-

Although it is not the perfect situation, it is common to use black pipe for the transfer of vegetable oil. Using SS would be the best but since there is not much moisture in vegetable oils the use of the SS with carbon steel flanges is more than sufficient for the situation you describe. During the later processing of vegetable oil it is usually heated, sometimes cooled and then passed through filter presses that remove contaminate particles such as rust and dirt particles and the moisture. Depending upon the type of oil they may also decant it prior to all of these steps to remove water.

When imported vegetable oils are received they often are transported in carbon steel storage tanks, transferred in carbon steel pipes, pumped with carbon steel pumps and then stored in carbon steel storage tanks. The further processing removed any unwanted contaminants.

When welding the Stainless to the carbon steel always use the alloy of the better metal. In this case you would use stainless steel rod or wire of the same grade or better of the stainless. For instance, if the Stainless is 304 uses 304 rod/wire, if 316 use 316 rod/wire. Although not the best way to do it, this is a common way to weld hangers and braces of carbon steel to the outside of stainless. You should have no unwanted galvanic effect on the piping.

If wet vegetable oils are stored in carbon steel tanks and have enough dwell time in the tanks, it is always the bottom or the lower sides that eventually rust out if they even do so. This is for very wet oils where there is enough time for the water to settle out. Just like a vinegar and oil salad dressing.

If the vegetable oil is food grade and destined for food in the USA this process may not be permitted due to the carbon flanges. The FDA sometimes sets their standards higher than realistically necessary.

I am very familiar with this type of processing and the example I have cited above. I was once involved with the whole operation of a facility using Castor Oil as the main raw material. Raw brought in as described as above, except all the piping and materials in contact were carbon steel. Only when the oil was transferred for processing was it then handled and processed in Stainless Steel. Barges were usually 1,000,000 gallons incoming and products went out in railcars, tankers, drums and down to 1 gallon containers.

Your situation is not unusual, although if it was me and going to be consumed or to have dermal contact, I would prefer all Stainless Steel.

Good Luck, Old Salt

__________________
Any day on the green side of the grass is a GREAT DAY!, --- me +++++++++. I believe creativity is an inherent part of everyone. --- Kermit T. Frog
Register to Reply Good Answer (Score 2)
2
Associate
Technical Fields - Project Managers & Project Engineers - New Member

Join Date: Mar 2013
Posts: 38
Good Answers: 2
#14

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/10/2013 10:26 PM

Check your specs again. Are you sure it is not calling out a lap joint? This would have the mating flanges same as pipe (SS) that is butt welded to the piping but the backing flanges are carbon steel. The carbon steel backing flanges are not in the product flow. This is also common with lighter SS pipe schedules such as 10, 20.

Register to Reply Good Answer (Score 2)
Anonymous Poster #1
#23
In reply to #14

Re: Corrosion of Stainless Pipes and Carbon Flanges

02/05/2021 9:11 AM

It seems gussosa might have missed or understood what a lap joint design is in the first place. The pipe-to-stub end weld should not be the issue, since alloys should match, hence filler shall be E-308. The potential issue should be in any case, galvanic corrosion in sites with high humidity environment/coastal area with accumulation of electrolyte in the crevice.

Register to Reply
Active Contributor

Join Date: Nov 2013
Posts: 16
Good Answers: 1
#16

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/11/2013 5:40 AM

I expect they want Thin Wall Stainless Steel Piping. It's far cheaper than schedule piping in stainless. The end of each tube has a formed thin flange butt-welded on, the Mild Steel Flange is slipped on loose before this is welded on. The Carbon steel is usually coated to prevent rust. Very common in the UK for potable water systems etc.

A little tricky to draw the pipe sections for manufacture as there are limited components and some dimensional constraints.

Register to Reply Score 1 for Good Answer
Guru
Canada - Member - New Member

Join Date: Jul 2013
Location: Canada but south of 49
Posts: 895
Good Answers: 20
#21

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/11/2013 4:02 PM

What is the application?? Handling vegetable oil, may require "food grade" specs, which would mean that everything should be stainless(at least 316). Material selection depends entirely on the application(temperature and pressure will also have to be considered).

As mentioned below, you will have to watch for galvanic reaction if you mix stainless and carbon steel, so double check the application before going any further.

__________________
Never stop learning
Register to Reply
Guru

Join Date: Jan 2010
Location: Mineral wells Tx
Posts: 630
Good Answers: 34
#22

Re: Corrosion of Stainless Pipes and Carbon Flanges

12/24/2013 4:46 AM

SS Flanges are expensive. Maybe this is the reason. After welding these flanges will be internal coating. Which one is the service?.

Register to Reply
Register to Reply 23 comments

Good Answers:

These comments received enough positive votes to make them "good answers".

"Almost" Good Answers:

Check out these comments that don't yet have enough votes to be "official" good answers and, if you agree with them, vote them!
Copy to Clipboard

Users who posted comments:

Anonymous Poster (1); bigg (3); Eleven (1); gussosa (7); JNB (3); Kevin LaPaire (1); lyn (3); old salt (1); PWSlack (1); Steve Batey (1); Whitephone (1)

Previous in Forum: Crystallization of Methamidophos   Next in Forum: Reduce the Evaporative Loss of Cooling Tower

Advertisement